Best scraper seals factory: Mechanical seals often need to be used in chemical applications. When confronted with some harsh chemicals, mechanical seals containing elastomers made of Viton, Kalrez or Chemrez can’t hold up. Because PTFE (polytetrafluoroethylene)or as most people know it Teflon ® , has a 0-14 ph range it usually will hold up. Like most materials every choice has an up and a down side. Because PTFE will handle most chemical applications, chemical attack is no longer an issue. One the down side PTFE wedges can cause fretting of your sleeve or shaft if you have not hard surfaced your shaft or sleeve (plasma coating). The stationary element of your seal will require a PTFE gasket. It’s not much good to have a PTFE on the rotary and then use an elastomer on the seat. We have seen it done, and because it is a static application some have gotten away with it, but it is not recommended. Most commonly the seat will be a L-shaped or Clamped mount style to allow space for a PTFE gasket to be used as the secondary sealing element. Read more info on spring seals.
The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart.
Rubber seals are a common type of basic component in sealing devices, and play a very important role in the contradiction between leakage and sealing. Using rubber seals is an important way to promote technological advancement and prevent and reduce environmental pollution. They are a class of rubber products that are widely used in sealing technology. Because rubber is a polymer material with valuable elasticity, a wide temperature range. It gives less stress in different media producing large deformation, which can provide contact pressure, compensate for leakage gap, and achieve the purpose of sealing.
The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.
Diffusion leakage: Driven by the concentration difference, the medium leaks through the material transfer generated by the sealing gap or the capillary of the sealing material. Diffusion is the result of molecular motion and is not unidirectional. When the sealing pressure difference is extremely small or in a vacuum state, or when sealing permeable substances such as nitrogen and hydrogen, as well as highly toxic and radioactive substances, special attention should be paid to the leakage and diffusion.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Discover more details at https://www.dmsseals.com/.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.
Select the appropriate sealing material: There are many types of sealing materials, including many metals, plastics and rubbers. The same material has different performances from different companies. On the other hand, the same seal has different performances in different working conditions or different sealing schemes, so it must be carefully considered when choosing. Note: Be sure to consider seals under the premise of a reasonable sealing scheme, then consider the sealing material, and then consider the seal manufacturer. If you don’t have enough sealing experience, it is best to consider the sealing company first, and let the sealing company consider the sealing scheme and other issues, such as DMS Seals Technology Co.,Limited.
The spring seal produced by DMS SEALS is perfect for being applied to extremely high-speed, very low-speed equipment with micro piston strokes and other special operating conditions. It can be used with rotary seals and maintains good sealing performance in violent shake and vibration motion environments. At the same time, our seals are extremely adaptable to a wide range of working media. It is resistant to a wide range of chemicals except for soluble alkali metals, high-temperature fluorine and chlorine trifluoride. Therefore, it works well with liquids such as oils and water with high and low temperature.
