5 MIG welding machines tips: how to become a better welder and how to select the best welding equipment. The arc is shaped like a cone, with the tip at the electrode and the base on the metal being welded. The closer the electrode is held to the metal, the smaller the base of the cone — but as you pull the electrode farther away, the base (and puddle) gets larger. If the puddle gets too large, gravity will simply pull it away from the base metal, leaving a hole. This is why thin-gauge metals are especially challenging for beginners. Perhaps the most important skill needed for TIG welding is moving the torch in a controlled manner, with steady forward movement, while keeping the gap between the tip of the electrode and the base metal consistently small — usually in the range of 1/8 inch to 3/16 inch. It requires a lot of practice to precisely control the arc length, keeping it as short as you can without allowing the electrode to touch the base metal or filler rod.
In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode.
A few tips on welding equipment, MIG and TIG welders, plasma cutters. ARC Welding : ARC welding is one of the oldest welding processes around. It uses either an AC or DC power supply to create an electric arc between the welding rod and the workpiece metal to melt the metals and join them together. This style of welding is relatively inexpensive and very portable but it does require some practice to get good consistent welds and the welds will probably require some arc weldercleaning up afterwards. ARC welding is less suited to welding thinner materials but there is a large range of specialist electrodes (welding rods) available for ARC welders depending on what materials you are welding. ARC welding is versatile but more suited to heavier applications.
MIG Welding Increases Welding Speed: In addition to welding aluminum and other softer metals, MIG-welding works faster, provides cleaner welds, and handles many different types of metals. The downside is its complexity. MIG Welders need direct currents, a steady stream of inert gas, and precise control of their torches. The amount of heat generated from MIG welding provides the deep penetration required for a strong weld, while also melting the feed wire rapidly enough to maintain a higher welding speed than other techniques. Given the inert gas required for MIG welding, keep in mind that this technique cannot be conducted in windy areas. The Right Stick Electrode Increases Welding Speed: There are three kinds of electrodes used for stick welding: fast-fill, fill-freeze, and fast-follow. While each electrode has its advantages, the fast-fill electrodes melt quickly and allow welders to work faster. See more details at MIG welder.
Put a glove, block of wood, folded up heat resistant cloth or something non-conductive on the welding table to rest your arms or elbows on and to protect your arms from shock hazard: Do you enjoy getting shocked? Me neither . tig welding aluminum with your high frequency switched to continuous means that the high freq is always looking for a path to follow. So even resting your forearm on the metal table can let that high frequency current bite you just when you least want it, like right when you are near and edge and you are being extra careful not to melt the edge away and then ZAP!. Who needs that? Put a glove, block of wood, folded up heat resistant cloth or something non-conductive on the welding table to rest your arms or elbows on and to protect your arms from shock hazard. Also do whatever it takes to rest your torch hand on a steady object. Again, a block of wood, a balled up tape ball etc can all be used to give you something to rest your torch hand on.
