Hydraulic seals provider right now in 2024: The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film. Discover even more info on wiper seals.
What are Mechanical Seals? Mechanical seals are devices that accommodate a rotating shaft while containing and preventing the fluid from leaking out of the enclosed housing. While different mechanical seal designs are available for pumping applications, most have three sealing points. Rotating face that rotates with the shaft; Stationary face fitted to the pump housing; Interface portion between the rotating and stationary face of the seal. These three sealing points ensure that the fluid contained within the pump housing does not leak while also preventing dust particles in the atmosphere from entering the housing. The mechanical seals are usually made up of different materials to prevent sticking. Typically, one side of the seal uses softer materials like carbon graphite, and the other is made of harder materials such as silicon carbide or ceramic alumina. However, hard materials are preferred for both surfaces if the pumping application involves abrasive fluids. In addition to the two materials, the sealing unit also comes with O-rings to seal the stationary face on the housing side and the rotating face on the shaft side. Springs are also used to keep both faces pressed. In most cases, the two faces of the seals are also lubricated to prevent friction and wear. Depending on the application, this fluid film can either be a separate lubricant or the process fluid itself.
Because the system pressure is high, the temperature is high, and the wear is particularly serious, the seal is required to have good wear resistance. Low coefficient of friction: For construction machinery such as excavators and pump trucks, the hydraulic system pressure is high, the cylinder action speed is fast, and the wear of the seal is particularly serious. Therefore, the friction coefficient of the seal must be low, so that the seal has good wear resistance and suitable life.
The O-ring seal, which is also called shaft seal, is noted for a reasonable compression and stretch rate to achieve a good sealing effect. It will not leak when it is sealed statically. At the same time, the O-ring size is properly matched to the groove size. The structure is simple and its installation is very close to the machine. Its most prominent advantage is its self-sealing effect, eliminating the need for periodic adjustments. We guarantee that the size and mounting grooves of all our O-rings are standardized, so they are cost-effective and easy to maintain. They have low frictional resistance and are suitable for occasions where the pressure is often alternating.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Since the scraper seal is made of the special material, PTFE, it has an impurity immersion function. Therefore, when combined with the piston rod seal and the metal bushing, it can prevent damage to the piston rod and prevent the accumulation of oil pressure. It has a diameter range of 3-1600mm and a temperature range of -30°C + 200°C. The wiper scraper seal can operate at speeds of up to 5 m/s. It has high wear resistance, tear resistance, low-temperature resistance and good strength. Our wiper seals can be used in combination with piston seals and anti-wear rings to prevent oil in the cylinder from being mixed with foreign matter, which causes damage to the working seal. It is especially suitable for piston rods with a large diameter. Moreover, it has a wide range of applications, such as agricultural machinery, injection moulding machines, forklifts, cranes and so on.
Destroy the leak: The working conditions of the sealing part are relatively bad, the thermal deformation is large, it is often subjected to vibration, impact, improper installation, excessive tightening force, repeated use, compression deformation, internal stress concentration, damage beyond the fatigue strength, material aging, deterioration, etc. will cause damage to leaks. This kind of leakage has the greatest impact and great harm, so it is necessary to strengthen prevention.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. See more information at https://www.dmsseals.com/.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.
